BenQ PB6240 - XGA DLP Projector Manual de usuario

WelcomePB6240 Digital ProjectorPortable SeriesUser’s Manual

Important safety instructions4Safety Instructions (Continued)11. Do not step on the projector or place any objects upon it. Besides probable physical

Introduction 5IntroductionProjector featuresThe projector integrates high-performance optical engine projection and a user-friendly design to deliver

Introduction6Shipping contentsThe projector is shipped with the cables required for connection to a PC and to video equipment. Carefully unpack and ve

Introduction 7Optional accessoriesProjector exterior viewFront / upper sideRear side1. Macintosh adapter2. 250W lamp module3. Ceiling mount kit4. Pres

Introduction8Bottom sideConnector panelRefer to "Positioning your projector" on page 12 for more information on making connections to variou

Introduction 9Controls and functionsExternal control panel1. Power (Refer to "Start up" on page 22 and "Shutdown" on page 27 for m

Introduction10Adjusts the size of the image.Rotate clockwise to enlarge the image or rotate counter-clockwise to make the image smaller.13. Focus ring

Introduction 1110. Blank (Refer to "Hiding the image" on page 26 for more information.)Used to hide the screen image. Press Blank again to r

Positioning your projector12Positioning your projectorChoosing a locationYour projector is designed to be installed in one of four possible installati

Positioning your projector 13Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting, and the v

CopyrightCopyright 2005 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a

Positioning your projector14How to determine the position of the projector for a given screen size:1. Select your screen size. 2. Refer to the table a

Positioning your projector 15• The recommended focus range is from 1500-8000 millimeters (1.5-8 meters).• There is 3%-5% tolerance among these numbers

Connection16ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

Connection 17• Many laptops do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key t

Connection18Connecting Video source devicesYou can connect your projector to various Video source devices that provide any one of the following output

Connection 19Connecting a Component Video source deviceExamine your Video source device to determine if it has a set of unused Component Video output

Connection20Connecting an S-Video source deviceExamine your Video source device to determine if it has an unused S-Video output socket available: • If

Connection 21Connecting a composite Video source deviceExamine your Video source device to determine if it has a set of unused composite Video output

Operation22OperationStart up1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check tha

Operation 232. When the function is activated for the first time, a prompt will display on the screen. Use the 5 or 6 button to select a number for ea

Table of contents iiiTable of contentsImportant safety instructions...1Introduction ...

Operation24Adjusting the heightThe projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These adjusters change the image

Operation 25Correcting keystoneKeystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs

Operation26Selecting an application modeThe projector is preset with several predefined application modes so that you can choose one to suit your oper

Operation 27Remote paging operationsYou can operate your display software program (on a connected PC) which responds to page up/down commands (like Mi

Operation28Menu operationMenu systemPlease note that the on-screen display (OSD) menus vary according to the signal type selected.*When a Video or S-V

Operation 29Using the menusThe projector is equipped with on-screen display (OSD) menus for making various adjustments and settings.There are 10 diffe

Operation301. Picture menu• Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown o

Operation 31Color Temp4 color temperature* settings are available.This value will be reset if you subsequently select an Application mode.1. T1: With

Operation322. Pro-Picture menuSome picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown

Operation 333. Setting menu FUNCTION DESCRIPTIONMuteToggles projector audio between on and off.VolumeAdjusts audio volume level. The default volume le

Table of contentsivAuto-adjusting the image ...24Fine-tuning the image size and clarity ...

Operation344. Advance menuFUNCTION DESCRIPTIONMirrorThe projector can be installed on a ceiling or behind a screen, or with one or more mirrors. Conta

Operation 35Economic ModeUse this mode to reduce system noise and reduce power consumption by 20%. If this mode is activated, the light output will be

Operation365. Information menuThis menu shows you the current operating status of the projector.Some picture adjustments are available only when certa

Maintenance 37MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep the

Maintenance38Lamp informationWarning messageWhen the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, plea

Maintenance 39• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.Step 1. Turn the

Maintenance40Step 8. Restart the projector.Do not turn the power on with the lamp cover removed. Step 9. Resetting the lamp counter Do not reset if th

Maintenance 41--The projector is under normal operation.Light Status & DescriptionPower Temp LampLamp events--(1) The projector needs 110 seconds

Maintenance42Service informationAccessories (included in the standard package) Optional accessories (not included in the standard package) Ordering pa

Maintenance 43Safety instructions for ceiling mounting of your BenQprojectorWe want you to have a pleasant experience using your BenQ projector, so we

Table of contents vSupported timing for Video and S-Video inputs ...46Dimensions ...

Troubleshooting44TroubleshootingThe projector does not turn on.No picture.Blurred image.Remote control does not work.Cause RemedyThere is no power fro

Specifications 45SpecificationsProjector specifications All specifications are subject to change without notice. GeneralProduct name Digital Projector

Specifications46Timing chartSupported timing for PC inputSupported timing for Component-YPbPr inputSupported timing for Video and S-Video inputsResolu

Specifications 47DimensionsUnit: mm

Warranty48WarrantyLimited WarrantyBenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of

Regulation Statements 49Regulation StatementsFCC statementCLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not i

Regulation Statements50<Memo>

Table of contentsvi<Memo>

Important safety instructions 1Important safety instructionsYour BenQ projector is designed and tested to meet the latest standards for safety of info

Important safety instructions2 Safety Instructions1. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 4

Important safety instructions 3 Safety Instructions (Continued)7. Do not place this projector in any of the following environments. - Space that