Benq MP522 Manual de usuario

WelcomeMP512/MP513/MP522 Digital ProjectorUser Manual

Introduction10Controls and functionsProjector7. BLANKUsed to hide the screen picture. See "Hiding the image" on page 37 for details.8. TEMPe

Introduction 11Remote control1. PowerToggles the projector between standby mode and on. See "Starting up the projector" on page 24 and "

Introduction12Remote control effective rangeInfra-Red (IR) remote control sensor is located on the front of the projector. The remote control must be

Positioning your projector 13Positioning your projectorChoosing a locationYour room layout or personal preference will dictate which installation loca

Positioning your projector14Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting (if availab

Positioning your projector 15How to determine the position of the projector for a given screen size1. Select your screen size.2. Refer to the table an

Positioning your projector16MP513/MP522 projection dimensionsRefer to "Dimensions" on page 56 for the center of lens dimensions of this proj

Positioning your projector 17MP512 projection dimensionsRefer to "Dimensions" on page 56 for the center of lens dimensions of this projector

Connection18ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

Connection 19Connecting a monitorIf you want to view your presentation close-up on a monitor as well as on the screen, you can connect the D-SUB OUT s

Table of contents2Table of contentsImportant safety instructions ...3Introduction...7Projector features ...

Connection20Connecting Video source devicesYou can connect your projector to various Video source devices that provide any one of the following output

Connection 21Connecting a Component Video source deviceExamine your Video source device to determine if it has a set of unused Component Video output

Connection22Connecting an S-Video source deviceExamine your Video source device to determine if it has an unused S-Video output socket available: • If

Connection 23Connecting a composite Video source deviceExamine your Video source device to determine if it has a set of unused composite Video output

Operation24OperationStarting up the projector1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where f

Operation 25Using the menusThe projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.Below is the overv

Operation26Utilizing the password functionFor security purposes and to help prevent unauthorized use, the projector includes an option for setting up

Operation 27Entering the password recall procedure1. Press and hold AUTO on the projector or remote control for 3 seconds. The projector will display

Operation28Switching input signalThe projector can be connected to multiple devices at the same time. However, it can only display one full screen at

Operation 29If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image

Important safety instructions 3Important safety instructionsYour projector is designed and tested to meet the latest standards for safety of informati

Operation30Correcting keystoneKeystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs

Operation 316. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.7. To reduce size of the picture, pr

Operation324. 16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio. This is most suitable for images whi

Operation 33Setting the User 1/User 2 modeThere are two user-definable modes if the current available picture modes are not suitable for your need. Yo

Operation34Adjusting ColorHighlight Color in the PICTURE menu and adjust the values by pressing / on the projector or remote control.Lower setting p

Operation 35Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color manag

Operation36Setting the presentation timerThe presentation timer can indicate the presentation time on the screen to help you achieve better time manag

Operation 37To cancel the timer, perform the following steps.1. Go back to the Presentation Timer page. 2. Press and press / to highlight Off and

Operation38• Keys on the remote control are still in use when panel key lock is enabled.• If you press Power to turn off the projector without disabli

Operation 39Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary t

Important safety instructions4 Safety Instructions (Continued)7. The lamp becomes extremely hot during operation. Allow the projector to cool for appr

Operation40Menu operationMenu systemPlease note that the on-screen display (OSD) menus vary according to the signal type selected.Main menu Sub-menu O

Operation 41Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the pro

Operation42Description of each menuFUNCTION(default setting/value)DESCRIPTION (default setting/value)Wall Color (Off)Corrects the projected picture’s

Operation 43FUNCTION(default setting/value)DESCRIPTION (default setting/value)Tint(0)Adjusts the red and green color tones of the image. See "Adj

Operation44FUNCTION(default setting/value)DESCRIPTION (default setting/value)Projector Position(Front Table)The projector can be installed on a ceilin

Operation 45FUNCTION(default setting/value)DESCRIPTION (default setting/value)Standby D-Sub Output(Off)Selecting On enables the function. The projecto

Operation46FUNCTION(default setting/value)DESCRIPTION (default setting/value)FAQ-Image and InstallationDisplays possible solutions to problems you may

Maintenance 47MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep the

Maintenance48Lamp informationGetting to know the lamp hourWhen the projector is in operation, the duration (in hours) of lamp usage is automatically c

Maintenance 49Timing of replacing the lampWhen the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please

Important safety instructions 5 Safety Instructions (Continued)13. Do not place this projector in any of the following environments.- Space that is p

Maintenance50Replacing the lamp• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one

Maintenance 515. Pull out the lamp connector from a slot in the lamp compartment. Disconnect it from the projector as illustrated.6. Lift the handle s

Maintenance5213. Restart the projector.Do not turn the power on with the lamp cover removed.Resetting the lamp timer14. After the startup logo, open t

Maintenance 53IndicatorsLight Status & DescriptionPower Temp LampPower eventsOrange Orange OrangeThe projector has just been connected to a power

Troubleshooting54TroubleshootingThe projector does not turn on.No pictureBlurred imageRemote control does not workThe password is incorrectCause Remed

Specifications 55SpecificationsProjector specifications All specifications are subject to change without notice. GeneralProduct name Digital Projector

Specifications56Dimensions255 mm (W) x 90 mm (H) x 214 mm (D)Timing chartSupported timing for PC input2552149061.566Resolution Horizontal Frequency (k

Specifications 57Supported timing for Component-YPbPr inputDisplaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibra

Warranty and Copyright information58Warranty and Copyright informationLimited warrantyBenQ warrants this product against any defects in material and w

Regulation statements 59Regulation statementsFCC statementCLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not i

Important safety instructions6Safety Instructions (Continued)17. Do not step on the projector or place any objects upon it. Besides probable physical

Introduction 7IntroductionProjector featuresThe projector integrates high-performance optical engine projection and a user-friendly design to deliver

Introduction8Shipping contentsCarefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contac

Introduction 9Projector exterior view1. External control panel (See "Projector" on page 10 for details.)2. Vent (heated air exhaust)3. Quick