Benq PB6110 Manual de usuario

WelcomePB6110 / PB6210 Digital ProjectorPortable SeriesUser’s Manual

Introduction6Shipping ContentsThe projector is shipped with the cables required for connection to a PC and to video equip-ment. Carefully unpack and v

Introduction 7Alternative Accessories1. Power Cord: 110V for the US, 240V for UK and 220V for European countries2. 3-2 power converter: For the US Opt

Introduction8Bottom SideConnector PanelRefer to page 12 for more information on making connections to various equipment.Lamp doorFront adjuster footRe

Introduction 9Controls and FunctionsExternal Control Panel131210911534872161. Power (Refer to pages 18 and 19 for more information.)Turns the projecto

Introduction10Remote Control Description Functions DescriptionsPowerTurns the projector on or off. Refer to pages 18 and 19 for more information

Introduction 11Remote Control Effective RangeInfra Red (IR) remote control sensors are located on the front and the back of the projector. The remote

Connection12ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

Connection 13Connecting Equipment to the Component VideoInputThe projector is capable of displaying various High Definition TV display modes. Some of

Connection14 If the selected video image is not displayed after the projector is turned on and the correctvideo source has been selected, check that t

Installation 15InstallationChoosing a LocationYour projector is designed to be installed in the four installation configurations shown here: Floor fro

CopyrightCopyright 2004 by BENQ Corporation. All rights reserved. No part of this publication may be repro-duced, transmitted, transcribed, stored in

Installation16Adjusting the HeightThe projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These adjusters change the im

Installation 17 There is 3% ~ 5% tolerance among these numbers due to optical component variations.* 1 m = 3.28 feet, 1 feet = 0.305 m, 1 m = 100 cm,

Operation18OperationStartup1. Switch all of the connected equipment on.2. Plug the power cord into the projector and into a wall socket.3. Turn on the

Operation 19Shutdown1. Press Power and a warn-ing message appears. Press Power a second time to turn the projector off. 2. The Power indicator light f

Operation20Digital Keystone CorrectionKeystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It

Operation 21Source SelectionTo sequentially select input sources, press Source on the projector control panel or the remote control. It may take you a

Operation22BlankIn order to draw the audience’s full attention to the presenter, you can use Blank to hide the screen image. Press Blank again to rest

Operation 23FreezeThe image is frozen when Freeze is pressed. An icon will appear in the lower right corner of the screen. To release the function,

Operation24Menu OperationMenu SystemPlease note that the OSD menus vary according to the signal type selected.*When a Video or S-Video signal is conne

Operation 25Using the MenusThe projector is equipped with on-screen display (OSD) menus for making various adjust-ments and settings.There are 10 diff

Table of Contents iiiTable of ContentsImportant Safety Instructions ... 1Introduction ...

Operation261. Picture MenuPC signal inputFUNCTION DESCRIPTIONPreset ModePreset modes are provided so you can optimize your projector image set-up to s

Operation 27Video/ S-Video/ Component Video signal inputFUNCTION DESCRIPTIONPreset ModeAs above.KeystoneAs above.BrightnessAs above.ContrastAs above.C

Operation282. Pro-Picture MenuPC signal inputVideo/ S-Video/ Component Video signal inputFUNCTION DESCRIPTIONAuto ResizeMakes the best fit of the imag

Operation 293. Setting Menu *About color temperatures:There are many different shades that are considered to be “white” for various purposes. One of t

Operation304. Advance MenuFUNCTION DESCRIPTIONMirrorThe projector can be installed on a ceiling or behind a screen, or with one or more mirrors. Conta

Operation 315. Information MenuThis menu shows you the current operating status of the projector.PC signal / Component Video inputVideo / S-Video sign

Maintenance32MaintenanceYour projector needs little maintenance. Things you have to do on a regular basis are keep the lens clean.Never remove any par

Maintenance 33Lamp InformationWarning MessageWhen the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, ple

Maintenance34Step 1. Turn the power off and disconnect the projector from the wall socket.Step 2. Turn the projector over. Then loosen the screws and

Maintenance 35Step 8. Resetting the lamp counter i. Press and hold the Exit 5 button on the projector for 5 seconds to display the total used lamp tim

Table of ContentsivFreeze ...23Preset Mode Selection ...

Maintenance36Light Status & DescriptionPower Temp LampLamp events--(1) The projector needs 110 seconds to cool down. Or(2) Please contact your dea

Maintenance 37Service InformationAccessories (included in the standard package) Optional Accessories (not included in the standard package) Ordering

Troubleshooting38TroubleshootingTHE PROJECTOR DOES NOT TURN ON.NO PICTUREBLURRED IMAGEREMOTE CONTROL DOES NOT WORKCause RemedyThere is no power from t

Specifications 39SpecificationsProjector Specifications All specifications are subject to change without notice. GeneralProduct name Digital Projector

Specifications40Timing ChartSupported Timing for PC InputSupported Timing for Component-YPbPr InputSupported Timing for Video and S-Video InputsResolu

Dimensions 41DimensionsUnit: mm26291.291.2215

Warranty42WarrantyLimited WarrantyBENQ warrants this product against any defects in material and workmanship, under normal usage and storage. Exclusio

Regulation Statements 43Regulation StatementsFCC StatementCLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not i

Important Safety Instructions 1Important Safety InstructionsYour BenQ projector is designed and tested to meet the latest standards for safety of info

Important Safety Instructions2 Safety Instructions1. The lamp becomes extremely hot during operation. Allow the projec-tor to cool for approximately

Important Safety Instructions 3 Safety Instructions (Continued)7. Do not place this projector in any of the following environments. - Space that

Important Safety Instructions4Safety Instructions (Continued)11. Do not step on the projector or place any objects upon it. Besides probable physical

Introduction 5IntroductionProjector FeaturesThe projector integrates high-performance optical engine projection and a user-friendly design to deliver